Audi Volkswagen ODIS 6.2 with license

 ODIS Service 7 Free Download

ODIS Service 7 Review

Diagnostic software Offboard Diagnostic Information System is a program that supports the interface compatible with SAE J2534 (diagnostic interface). This software allows you to diagnose all car brands Volkswagen, Audi, Skoda, Seat, Bentley, and Lamborghini. You can also download Light Tracer Render 2

It has the following diagnostic interface VAS:

  ●VAS 6154(supports WLAN) (Windows 7 + Windows 10)
  ●VAS 5054A (radio on Bluetooth) (Windows 7)
  ●VAS 5055 (with cable connection through the USB connector) (the Windows 7)
  ●Commissioning appropriate unit must be connected to the diagnostic tester via the     USB connector, and before starting the ODIS Service install the appropriate drivers.     To install the software may require administrator privileges.
  ● New version program Vozmozhno installs on VirtualBox

Technical Details of ODIS Service 7

    Software Name: ODIS Service for Windows
    Software File Name: OffboardDiagSetup-Service_VWMCD_721.rar
    Software Version: 7.2.1
    File Size: 16.6 GB
    File Password: 123
    Language: English
    Working Mode: Offline (You don’t need an internet connection to use it after installing)

System Requirements for ODIS Service 7

    Operating System: Windows 10/11
    Free Hard Disk Space: 16 GB
    Installed Memory: 4 GB
    Processor: Intel Dual Core processor or later
    Minimum Screen Resolution: 800 x 600

How to set up VAS 6154 wifi

Step 1: Input the fourth CD and open it and then install the vas 6154 driver

Step 2: Open the CD and then chose the vas 6154 driver to install

Step 3: After installed and click on the Desktop – symbol

Step 4: Click on the Device Configuration

Step 5: Choose the connection way “WLAN”

Step 6: Choose the “save”

Step 7: Plug the vas 6154 to the car

Step 8: Open the WIFI and find the VAS-6154 wifi name and connect it.

Step 9: It shows Connected

Step 10: The state of connect successfully

Step 11: Open odis software. Now the latest version is 4.4.1

Step 12: VAS 6054 wifi connection setup successfully.

Done! Ready for use!

 How to flash engine ecu with VAS6154 and Odis Engineering

 1.Open odis enginineer,connect to VAS 6154, select model series;

2.Diagnostic entrance;

3.Select flash file;

4.Start flashing;

5.Flashing successful.

 Component Unlocking with ODIS on VWAudi

Volkswagen & Audi introduced component lock (anti-theft/immobilizer) function to their newer transmission control modules to help fighting unauthorized swap of the control unit. If a TCU/TCM is faulty and has been replaced, a component unlock is therefore required.

Note: You don’t need to unlock the unit if you choose to clone the SW from your original unit to the new one.

Typical error messages:

Contains Component protection (Component protection active)
The control unit is currently associated with a VIN other than the vehicle VIN or the control unit VIN

You need the following tools to perform component unlock:

VAG diagnosis tool (like VAS5054A, VAS 6154) to connect to your vehicle
ODIS software
A VW/Audi account depending on the vehicle

Procedure for unlocking TCU:

Run a diagnosis in your ODIS software
Locate and select the entry “Component protection”
Click on “Perform test…”
Click on “Done/Continue”
Enter the required information. (Activation number can be your own record number)
Enter your VW/Audi online account credentials
Click on “OK”
On success, ODIS should display “The component protection base programming has been carried out successfully.”
Click on “Done”
Follow the instructions provided by ODIS
End of your component base programming
Go back to the test screen and you should see a green check mark before component protection
Perform basic settings using guided functions
Erase your previous fault codes
You may now load your SW into the TCU if needed. If you don’t have the flash program, you may contact your Shing Hoi representative.

Autel MaxiIM Series IMMO Programming Tool new released Autel MaxiIM KM100 universal key generator kit. Compare with Autel MaxiIM IM508 and IM608, Autel KM100 support universal Transponder & Key Generation,Transponder Simulation Editing & Cloning and Ignition Coil Detection. Autel KM100 is not support vehicle diagnostic and service functions.

Autel IM608 VS IM508 VS KM100 Comparison Table:

Install TIS2000 for GM Tech2 Instruction

1) Insert TIS2000 software CD into the laptop
2) Install the setup driver in the CD
3) Select Activator. Select first one Activator hardware key
4) Load DATA DVD (tis2000+data+0802) to run TIS200 on desktop after compete install the setup. TIS2000 will update the data automatically.
5) Find out and locate SuperPro.dll file in TIS2000 crackfile folder after update data and copy the SuperPro.dll file to “C:Program filescosidsbin”
6) Then run TSI2000 software
7) Connect GM Tech2 device with computer
8) Start ECU programming and follow the windows prompts.
If you order GM Tech2 scanner with Saab software, you’d better choose Saab TIS2000 CD with USB key.

GM TECH2 Screen Shows:

 How does VW AUDI ODIS set the car brand

1.Open ODIS（use VAS 6154A connect）

2.Admin-General-Brand design-selection-save.（VW, AUDI, Bentley, Lamborghini, Skoda, MAN, Volkswagen commercial vehicles, and Seattle have the same setting method）

3.Admin-Connection-Brand settings-Selection-save.（VW, AUDI, Bentley, Lamborghini, Skoda, MAN, Volkswagen commercial vehicles, and Seattle have the same setting method）

PIWIS 3 how to import certificates

1.Use the task manager to enter the computer desktop, you can use the key combination, press ESC+shift+Ctrl, or Ctrl+Alt+Del;

 

In the task manager window, select “File”-“Run newtask”, enter explorer, “open” to show the windows desktop;

2.Windows desktop, move the mouse to the task bar at the bottom of the screen. Right-click on the taskbar-select “Show the desktop” to show the windows computer desktop.

3.Click This PC or file browser, open My Computer, browse to find the certificate file.

4.Double-click the certificate file PPNL, and you will be prompted to enter the password. After entering the password, click Import certificate, and the certificate file is imported successfully.
（You can use the remote software to transfer the certificate file, or download it to the Windows hard disk by email.）

If you cannot use a USB flash drive to copy files to your computer, you can use your email, Microsoft onedrive or mega network disk, upload the file and download it to the Porsche computer disk via the network.(Because of the Porsche Piwis system, mobile devices are prohibited)

If you want to install software or drivers, you need to use Task Manager to Stop AdminService.